产品分类
带显示导轨电源
接近开关联系我们
电话: 0577-61510353
传真: 0577-61510353
E-mail: info@chance-electric.com
E-mail: yqchux@126.com
地址: 浙江省乐清市新光工业区柳乐路63号乐清市电子商务产业园8楼801
Skype: zheng.janson
QQ:
3572813688
|
| 产品详细: | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Open Frame Power Supply PS-35 35w On Board Type SMPS
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Specification | Model | |||
| PS-35W-5V | PS-35W-12V | PS-35W-15V | PS-35W-24V | |
| DC output | 5V 6A | 12V 3A | 15V 2.4A | 24V 1.5A |
| Wave and noise | 100mVP-P | 120mVP-P | 150mVP-P | 200mVP-P |
| Inlet stability | ±0.5% | ±0.5% | ±0.5% | ±0.5% |
| Load stability | ±1% | ±0.5% | ±0.5% | ±0.5% |
| Efficiency | 78% | 81% | 81% | 85% |
| VOLTAGETOLERANCE | ±3.0% | ±2.0% | ±2.0% | ±2.0% |
| AC input voltage range | 85 ~ 264VAC 120 ~ 370VDC | |||
| AC CURRENT (Typ.) | 0.4A/115VAC 0.2A/230VAC | |||
| INRUSH CURRENT (Typ.) | COLD START 40A/230VAC | |||
| LEAKAGE CURRENT | <0.5mA / 240VAC | |||
| OverLoad protection | 105%~150%hiccup mode ,auto-recovery | |||
| Setup,rise,hold up time |
5 ~ 24V:1200ms, 30ms 48V:1200ms, 75ms at full load |
|||
| Withstand voltage | I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC | |||
| Isolation resistance | I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC | |||
| Working temperature | --10 ~ +60°C (Refer to output load derating curve) | |||
| WORKING HUMIDITY | 20 ~ 90% RH non-condensing | |||
| Safety standards | Design refer to GB4943,UL60950,EN60950 | |||
| EMC standards | Design refer to GB9254,EN55022 classA | |||
| DIMENSION | 101.6*50.8*24mm (L*W*H) | |||
| PACKING | 0.124Kg;96PCS/12.9Kg/0.8CUFT | |||
| NOTE |
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25°C of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. |
|||
| 相关产品 : |
|
|
|
